Quick quote: Rohde & Schwarz ZNA26 (1332.4500.24)

Rohde & Schwarz ZNA26 (1332.4500.24)

Vector Network Analyzer; 4 Port, 3.5 mm Connector, 10 MHz to 26.5 GHz
Model
ZNA26 (1332.4500.24)
Product Family
RF & Microwave Network Analyzers
Manufacturer
Rohde & Schwarz

Configured models contain the following attributes:

RF & Microwave Network AnalyzersNetwork Analyzers >=20GHz20GHz <= 50GHz1MHz <= 10MHz3.5mm-Male (Jack)Benchtop
Configurations
Key Specs
Product Overview
Resources

Choose your configuration

Show:

Available Options for Rohde & Schwarz ZNA26 (1332.4500.24)

OptionDescription
Precision frequency reference for R&S®ZNA (Hardware option)
2nd internal LO source, for R&S®ZNA (4 ports) external access up to 26.5 GHz requires option R&S®ZNA-B8 in addition (Hardware option)
Memory extension for long time data recording, data streaming, extended pulse pattern recording for R&S®ZNA (Hardware option)
mmWave converter LO, 10 MHz to 26.5 GHz, for R&S®ZNA Enables mmWave converter setups utilizing a R&S®ZNA, or general external (IF) mixing. (used for mmWave-converter setups: Requires one of options R&S®ZNA-B26, ""Direct IF access"", or R&S®ZNA-B5, ""2nd internal LO src"". Used as general mixer LO: Requires R&S®ZNA-B5, ""2nd internal LO src"") (Hardware option)
Direct IF access for R&S®ZNA (Hardware option)
Additonal trigger and control I/O ports for R&S®ZNA 3 trigger in, 4 trigger out, 4 pulse modulator control ports (I/O switchable), busy and ready for trigger indication, noise source control (28 V), RF OFF control input (Hardware option)
Spectrum analyzer mode for R&S®ZNA (software license)
Time domain analysis (TDR) for R&S®ZNA (software license)
Scalar mixer measurements and arbitrary frequency-converting measurements for R&S®ZNA (software license)
Vector corrected converter measurements (without reference mixer and phase reference) for R&S®ZNA requires R&S®ZNA-K4 (software license)
Measurements on pulsed signals (Pulse configuration, pulse profile and pulse train measurements) for R&S®ZNA requires R&S®ZNA-K17 (software license)
mmWave converter support for R&S®ZNA, R&S®ZVA-Zxxx, R&S®ZCxxx (software license)
Group delay measurements on frequency converters without LO access for R&S®ZNA (4 ports recommended) requires R&S®ZNAxx-B16/R&S®ZNA-K4 (software license)
Increased IF bandwidth up to 30 MHz for R&S®ZNA (software license)
1 mHz frequency resolution for R&S®ZNA (software license)
Extended time domain analysis incl. eye diagram for R&S®ZNA requires R&S®ZNA-K2 (software license)
Noise figure measurements on 2-port devices for ZNA (ZNAxx-B16/-B2x recommended) (software license)
3rd and 4th internal source for R&S®ZNA26 (4 ports) (Hardware option)
Direct source and receiver access for R&S®ZNA26 (4 ports) Installation ex factory only (Hardware option)
Source step attenuator for port 1, mechanical, 70 dB in 10 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)
Source step attenuator for port 2, mechanical, 70 dB in 10 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)
Source step attenuator for port 3, mechanical, 70 dB in 10 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)
Source step attenuator for port 4, mechanical, 70 dB in 10 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)
Receiver step attenuator for port 1, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)
Receiver step attenuator for port 2, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)
Receiver step attenuator for port 3, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)
Receiver step attenuator for port 4, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)
Internal pulse modulator for port 1 for R&S®ZNA26 (Hardware option)
Internal pulse modulator for port 2 for R&S®ZNA26 (Hardware option)
Internal pulse modulator for port 3 for R&S®ZNA26 (Hardware option)
Internal pulse modulator for port 3 for R&S®ZNA26 (Hardware option)
Direct source monitor access, port 1, R&S®ZNA26 (HW opt.)
Internal combiner for port 1 and port 3 for R&S ZNA26 (4 ports) Provides a two-tone signal at Port 1, combining the internal sources of Port 1 and Port 3 (Hardware option. Requires R&S ZNA26-B21 and R&S ZNA26-B23)
Internal combiner for port 1 and port 3 for R&S®ZNA26 (4 ports). Provides a two-tone signal at Port 1, combining the internal sources of Port 1 and Port 3. Upgrade / retrofit by R&S service Memmingen only. (Hardware option. Requires R&S®ZNA26-B21 and R&S®ZNA26-B23)
Low noise pre-amplifier receiver port 2

Showing 1 - 6 of 11 results

1
2
1

Vector Network Analyzer, 4 ports 10 MHz to 26.5 GHz, 3.5 mm (m) connectors

Product ID: P-558729

ZNA26-B21 (1332.4630.21) • Source step attenuator for port 1, mechanical, 70 dB in 10 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)ZNA26-B213 (1332.4846.13 ) • Internal combiner for port 1 and port 3 for R&S ZNA26 (4 ports) Provides a two-tone signal at Port 1, combining the internal sources of Port 1 and Port 3 (Hardware option. Requires R&S ZNA26-B21 and R&S ZNA26-B23)ZNA26-B16 (1332.4581.24) • Direct source and receiver access for R&S®ZNA26 (4 ports) Installation ex factory only (Hardware option)ZNA-K9 (1332.5394.02) • Group delay measurements on frequency converters without LO access for R&S®ZNA (4 ports recommended) requires R&S®ZNAxx-B16/R&S®ZNA-K4 (software license)ZNA-B8 (1332.4652.02) • mmWave converter LO, 10 MHz to 26.5 GHz, for R&S®ZNA Enables mmWave converter setups utilizing a R&S®ZNA, or general external (IF) mixing. (used for mmWave-converter setups: Requires one of options R&S®ZNA-B26, ""Direct IF access"", or R&S®ZNA-B5, ""2nd internal LO src"". Used as general mixer LO: Requires R&S®ZNA-B5, ""2nd internal LO src"") (Hardware option)ZNA-K4 (1332.5342.02) • Scalar mixer measurements and arbitrary frequency-converting measurements for R&S®ZNA (software license)
Rent

Availability confirmed on quote

Quote

Used

Availability confirmed on quote

Inquire

Looking For New?

This product may be available by an alternative finance solution.

2

Vector Network Analyzer, 4 ports 10 MHz to 26.5 GHz, 3.5 mm (m) connectors

Product ID: P-250366

ZNA26-B42 (1332.4775.42) • Internal pulse modulator for port 2 for R&S®ZNA26 (Hardware option)ZNA26-B32 (1332.4700.32) • Receiver step attenuator for port 2, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)ZNA26-B16 (1332.4581.24) • Direct source and receiver access for R&S®ZNA26 (4 ports) Installation ex factory only (Hardware option)ZNA-B26 (1332.4598.02) • Direct IF access for R&S®ZNA (Hardware option)ZNA-B8 (1332.4652.02) • mmWave converter LO, 10 MHz to 26.5 GHz, for R&S®ZNA Enables mmWave converter setups utilizing a R&S®ZNA, or general external (IF) mixing. (used for mmWave-converter setups: Requires one of options R&S®ZNA-B26, ""Direct IF access"", or R&S®ZNA-B5, ""2nd internal LO src"". Used as general mixer LO: Requires R&S®ZNA-B5, ""2nd internal LO src"") (Hardware option)ZNA26-B22 (1332.4630.22) • Source step attenuator for port 2, mechanical, 70 dB in 10 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)
Rent

Availability confirmed on quote

Quote

Used

Availability confirmed on quote1

$172,730.00*$307,535.00

Looking For New?

This product may be available by an alternative finance solution.

3

Vector Network Analyzer, 4 ports 10 MHz to 26.5 GHz, 3.5 mm (m) connectors

Product ID: P-558730

ZNA26-B21 (1332.4630.21) • Source step attenuator for port 1, mechanical, 70 dB in 10 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)ZNA26-B32 (1332.4700.32) • Receiver step attenuator for port 2, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)ZNA26-B31 (1332.4700.31) • Receiver step attenuator for port 1, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)ZNA26-B34 (1332.4700.34) • Receiver step attenuator for port 4, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)ZNA-K30 (1332.5465.02) • Noise figure measurements on 2-port devices for ZNA (ZNAxx-B16/-B2x recommended) (software license)ZNA26-B16 (1332.4581.24) • Direct source and receiver access for R&S®ZNA26 (4 ports) Installation ex factory only (Hardware option)
Rent

Availability confirmed on quote

Quote

Used

Availability confirmed on quote

Inquire

Looking For New?

This product may be available by an alternative finance solution.

4

Vector Network Analyzer, 4 ports 10 MHz to 26.5 GHz, 3.5 mm (m) connectors

Product ID: P-558728

ZNA26-B32 (1332.4700.32) • Receiver step attenuator for port 2, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)ZNA26-B34 (1332.4700.34) • Receiver step attenuator for port 4, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)ZNA-K8 (1332.5388.02) • mmWave converter support for R&S®ZNA, R&S®ZVA-Zxxx, R&S®ZCxxx (software license)ZNA-B8 (1332.4652.02) • mmWave converter LO, 10 MHz to 26.5 GHz, for R&S®ZNA Enables mmWave converter setups utilizing a R&S®ZNA, or general external (IF) mixing. (used for mmWave-converter setups: Requires one of options R&S®ZNA-B26, ""Direct IF access"", or R&S®ZNA-B5, ""2nd internal LO src"". Used as general mixer LO: Requires R&S®ZNA-B5, ""2nd internal LO src"") (Hardware option)ZNA26-B21 (1332.4630.21) • Source step attenuator for port 1, mechanical, 70 dB in 10 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)ZNA26-B33 (1332.4700.33) • Receiver step attenuator for port 3, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)
Rent

Availability confirmed on quote

Quote

Used

Availability confirmed on quote

Inquire

Looking For New?

This product may be available by an alternative finance solution.

5

Vector Network Analyzer, 4 ports 10 MHz to 26.5 GHz, 3.5 mm (m) connectors

Product ID: P-549303

ZNA26-B3 (1332.4523.02) • 3rd and 4th internal source for R&S®ZNA26 (4 ports) (Hardware option)ZNA26-B32 (1332.4700.32) • Receiver step attenuator for port 2, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)ZNA-K7 (1332.5371.02) • Measurements on pulsed signals (Pulse configuration, pulse profile and pulse train measurements) for R&S®ZNA requires R&S®ZNA-K17 (software license)ZNA-B26 (1332.4598.02) • Direct IF access for R&S®ZNA (Hardware option)ZNA-B8 (1332.4652.02) • mmWave converter LO, 10 MHz to 26.5 GHz, for R&S®ZNA Enables mmWave converter setups utilizing a R&S®ZNA, or general external (IF) mixing. (used for mmWave-converter setups: Requires one of options R&S®ZNA-B26, ""Direct IF access"", or R&S®ZNA-B5, ""2nd internal LO src"". Used as general mixer LO: Requires R&S®ZNA-B5, ""2nd internal LO src"") (Hardware option)ZNA26-B44 (1332.4775.44) • Internal pulse modulator for port 3 for R&S®ZNA26 (Hardware option)
Rent

Availability confirmed on quote

Quote

Used

Availability confirmed on quote

Inquire

Looking For New?

This product may be available by an alternative finance solution.

6

Vector Network Analyzer, 4 ports 10 MHz to 26.5 GHz, 3.5 mm (m) connectors

Product ID: P-549304

ZNA26-B3 (1332.4523.02) • 3rd and 4th internal source for R&S®ZNA26 (4 ports) (Hardware option)ZNA26-B41 (1332.4775.41) • Internal pulse modulator for port 1 for R&S®ZNA26 (Hardware option)ZNA26-B32 (1332.4700.32) • Receiver step attenuator for port 2, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)ZNA26-B302 (1332.4752.12) • Low noise pre-amplifier receiver port 2ZNA-B26 (1332.4598.02) • Direct IF access for R&S®ZNA (Hardware option)ZNA26-B31 (1332.4700.31) • Receiver step attenuator for port 1, mechanical, 35 dB in 5 dB steps for R&S®ZNA26 Installation ex factory only (Hardware option)
Rent

Availability confirmed on quote

Quote

Used

Availability confirmed on quote

Inquire

Looking For New?

This product may be available by an alternative finance solution.

Showing 1 - 6 of 11 results

1
2
NOTE: If you’re in Canada, please use the ‘Quote’ option. Online Purchase is currently only available for US addresses, either via Card or Purchase Order.

How do I select a configuration?

You can scroll through configurations, search for options (separated by ;) above, and filter by Rental, New & Used. Or, let our experts guide you to the right solution by simply using ‘Quick Quote’ at the top of the page.

What’s the difference between Quote and Buy?

You can request a Quote for any item. Many New and Used items are also available to Buy online! You can mix your cart with items to Quote and items to Buy online. You’ll be able to complete the Quote and Buy checkout process at the same time. To check details, simply use ‘Quote’ and we’ll confirm everything. You can now buy either by card or by supplying a Purchase Order (P.O.). Note that P.O's will require verification and account set-up if you do not have an account.

Can I add extra items or make special requests?

Look out for the ‘Additional Information’ field when submitting your details. Use this for extra accessory or special calibration requests or for special delivery instructions. We’ll contact you when we receive your Order or Quote to fulfil.

* Prices & availability are subject to change without notice. All prices may vary due to shipping terms, sales tax, import duties, and exchange rates. Products may not be available in all locations. Any listed savings are based on the full list price of new instruments and are indicative depending on date of list; actual savings may vary based on option(s), configuration, currency exchange rates, and other factors. Warranty may vary by category or specific available product. All terms to be confirmed by full written quote or available to review in the Payment page when you buy online.
1 For Certified Pre-Owned equipment, units go into 23-step certification checks before shipping and we will confirm lead times.

Can't find what you are looking for?

Get in touch
Can't find what you are looking for?
loader
loader logo