The Model 250S1G6C is a solid-state, Class A design, self-contained, aircooled, broadband power amplifier designed for applications where instantaneous bandwidth, high gain and linearity are required. It will provide a minimum of 250 W across its operating bandwidth of 1.0 - 6.0 GHz. Protection from input overdrive beyond 0 dBm is provided as well as protection from various failure conditions including over-temperature and power supply faults.
A front panel display indicates the operational status and fault conditions. All amplifier control functions, and status indications are available remotely using GPIB/IEEE-488, RS-232, fiber-optic serial, USB, or Ethernet. Interface connectors are located on the back panel. Local and remote operation is managed by a switch on the front panel.
This is a multiple purpose amplifier. The low level of spurious signals and linearity make it ideal for use as a driver in testing wireless and communication components and subsystems. By covering such a wide bandwidth, it is suitable for 5G testing applications. Due to the Class A design, it is also suitable for EMC Test applications where continued operation into high VSWR loads including open and short circuits is required.
Key Features |
250 W CW, 1.0 - 6.0 GHz |
Class A design |
100% mismatch tolerant |
Built-in fault monitoring and protection |
Remote control: Ethernet, USB, GPIB, fiber-optic serial, RS-232 |
Modular design for easy maintenance and service |
Low acoustical noise |
Applications |
EMC (military, aviation, automotive, commercial) |
Radiated and conducted EMC testing |
General purpose, antenna, and component testing |
Specifications |
|
|
|
|
Model 250S1G6C
Solid-State Broadband Power Amplifier
|
|
|
|
|
Feature | Symbol | Minimum | Typical | Maximum |
Rated Power Output
(1.0 – 6.0 GHz)
| PSAT | 250 W | 350 W | >425 W |
Input for Rated Output | Pin | - | - | 1.0 mW
0 dBm
|
Power Output @ 3 dB Compression | P3dB | 225 W | 325 W | >400 W |
Power Output @ 1 dB Compression | P1dB | 200 W | 275 W | >375 W |
Operating Frequency | BW | 1.0 GHz | - | 6.0 GHz |
Gain
(Small Signal)
| - | 58 dB | 61 dB | 63 dB |
Gain Reduction Adjustment
(when below compression)
| - | 10 dB | 12 dB | 15 dB |
Flatness | ∆G | - | ±1.5 dB | ±2.5 dB |
Input Impedance | Z in | -
-
| 50 Ohm
1.5:1 VSWR
| -
2.0:1 VSWR
|
Output Impedance | Z out | - | 50 Ohm | - |
Specifications |
|
Model 250S1G6C
Solid-State Broadband Power Amplifier
|
|
Feature | Parameter |
Mechanical Specifications | Dimensions (With Cabinet) (W x H x D):
50.3 x 47 x 65.3 cm
19.8 x 18.5 x 25.7 in
Dimensions (No Cabinet) – 10U for 19” Rack:
48.3 x 44.5 x 65.3 cm
19.0 x 17.5 x 25.7 in
Weight (With Cabinet): 58.5 kg / 129 lb
Weight (No Cabinet): 44.9 kg / 99 lb
|
Connector Interface | RF input - N female (50 Ω)
RF output - 7-16 DIN female (50 Ω)
RF Sample - N female (50 Ω) (54dB typical)
IEEE-488 - 24-pin female
RS-232 - 9-pin subminiature D female
RS-232 (fiber optic) - ST
USB 2.0 - Type B
Ethernet - RJ-45
Interlock - 15-pin subminiature D female
AC - C20
|