Tektronix DSA72004 TEK-DSA72004 20GHz 4CH Digital Serial Analyzer
The DSA70000 Series is a real-time digital serial analyzer that is optimized
for verifying, characterizing, debugging and testing sophisticated high-speed
serial designs.
The TEK-DSA72004 comes bundled with the following application software:
JA3 - Advanced Jitter Analysis
RTE - Real Time Eye for Serial Testing
PTH - Serial Protocol Trigger and Decode
MTH - Serial Communications Mask Testing
2XL - 20Mpts Memory
ASM - Advanced Event Search and Mark - added Sept 2007
Specifications:
Bandwidth: 16GHz Analog, 18 & 20GHz user-selectable DSP enhanced bandwidth.
Sample Rate: 50GS/s on all 4 channels
Standard Memory: 20M per channel on all 4 channels (Opt 2XL)
Maximum Memory: 200M per channel on all 4 channels (Opt 20XL)
Waveform Capture Rate: > 300,000 wfms/second on all 4 channels
Serial Pattern Triggering up to 3.125 Gb/s with 8 b/10 b Protocol Triggering
for Isolation of Pattern-dependent Effects
Standard features include 12.1 in XGA 1024 x 768 display, Windows XP Pro.
Memory Upgrades:
TEK-DPO7UP/XL05 Memory Upgrade 20Ms to 50Ms per ch
TEK-DPO7UP/XL010 Memory Upgrade 20Ms to 100Ms per ch
TEK-DPO7UP/XL020 Memory Upgrade 20Ms to 200Ms per ch
Software Options:
PCE - PCI Express Compliance Module
IBA - InfiniBand Compliance Module
FBD - FB-DIMM Compliance Module
SST - Serial ATA, SAS Compliance Module
HT3 - HDMI Compliance Testing
ET3 - Ethernet Compliance Testing
USB - USB Compliance TestingAnalysis
DVI - DVI Compliance Test Solution
PWR - Power Measurement and Analysis
VNM - CAN/LIN Timing and Protocol Decode
J2 - Disk Drive Analysis Software
DJA - Jitter Eye Advanced Tools (via DJUP upgrade)
Input/Output Ports
Front Panel
Aux Trigger Input - See trigger specifications.
Recovered Clock - SMA connector, =/<1.25 Gb/s,
Output swing =/>130 mVpk-pk into 50 ohm at 1.25 Gb/s.
Requires Opt. PTH or Opt. MTH to enable on DPO70000, standard on DSA70000.
Recovered Data - SMA connector, =/<1.25 Gb/s,
Output swing of 1010 repeating pattern 200 mV into 50 ? at 1.25 Gb/s. Requires
Opt. PTH or Opt. MTH to enable on DPO70000, standard on DSA70000.
DC Probe Calibration Output - BNC connector,
10 V DC for DC probe calibration. (Signal available
only during probe calibration.)
Fast Edge Output - SMA connector provides fast edge signal. 1 kHz 20%; 810 mV
(base to top) 20% into =/>10 kohm load; 440 mV 20% into a 50 ohm load.
AUX Trigger Output - BNC connector, provides a TTL-compatible, polarity
switchable pulse when the oscilloscope triggers.
USB2.0 Port - One in front, four on back. Allows connection or disconnection
of
USB keyboard, mouse or storage device while oscilloscope is on.
Rear Panel
External Time Base Reference In - BNC connector; allows time base system to
phase lock to external 10/100 MHz reference.
Time Base Reference Out - BNC connector;
provides TTL-compatible output of internal 10 MHz reference oscillator.
AUX Trigger Output - BNC connector, 0 to 3 V; default output is A-Event
Trigger
low true.
Parallel Port - IEEE 1284, DB-25 connector.
Audio Ports - Miniature phone jacks for stereo microphone input and stereo
line
output.
USB2.0 Ports - Four in back. Allow connection or disconnection of USB
keyboard,
mouse or storage device while oscilloscope power is on.
Keyboard Port - PS/2 compatible. Mouse Port - PS/2 compatible.
LAN Port - RJ-45 connector, supports 10Base-T, 100Base-T and 1000Base-T.
Serial Port - DB-9 COM1 port.
Windows Video Port - 15-pin D-sub connector on the rear panel; connects a
second monitor to use dual-monitor display mode allowing analysis results and
plots to be viewed along with the oscilloscope display. Video is DDC2B
compliant.
GPIB Port - IEEE 488.2 standard.
Scope XGA Video Port - 15-pin D-sub connector on the rear panel, video is IBM
XGA compatible. Connects to show the oscilloscope display, including live
waveforms on an external monitor or projector. The primary Windows desktop can
also be displayed on an external monitor using this port.
TekLink - Proprietary interface for connecting multiple Tektronix instruments.
Power - 100 to 240 VRMS, 10%, 50/60 Hz;
115 VRMS 10%, 400 Hz; CAT II, <1100 VA typical.
ER's P1 bundle consists of the following options:
/PCE PCI Express SW
/SST SAS Serial ATA SW for RTE
/HT3 HDMI Compliance
/RTE Real Time Eye
/USB USB 2.0 Compliance
ER's P2 bundle consists of the following options:
/PCE PCI Express SW
/SST SAS Serial ATA SW for RTE
/USB USB 2.0 Compliance
/DJA Jitter Eye Adv Tools
/DDRA DDR Memory Technology
ER's P3 bundle consists of the following options:
/5XL 50Mpts mem per CH
/DVI DVI Compliance Software
/FBD FB-DIMM Compliance
/PCE PCI Express SW
/SST SAS Serial ATA SW for RTE
/USB USB 2.0 Compliance
ER's P4 bundle consists of the following options:
/5XL 50Mpts mem per CH
/DJA Jitter Eye Adv Tools
/DVI DVI Compliance Software
/FBD FB-DIMM Compliance
/PCE PCI Express SW
/SLA Serial Link Advanced SW
/SST SAS Serial ATA SW for RTE
/USB USB 2.0 Compliance |